German engineers offer 3,000-mile business jet design to industry

The Piero development team says one key to the design’s efficiency is the ratio of cabin volume to outside surface area.
A German engineering team has completed pre-development of a light jet it claims can fly twice as far as its competitors on similar fuel reserves. It is looking to partner with an established manufacturer to take the design forward.
The computations show that, if realised, the aircraft, known as PieroJet PJ-3, could fly 3,000 miles (4,830km) with IFR reserves. It has a fuel capacity of 1,800 litres. Using the example of the Spirit of St Louis, the aircraft that Charles Lindbergh flew on the first solo nonstop crossing of the Atlantic Ocean with a 1,700-litre fuel tank in 1927, team leader Stefan Piero Unzicker asks: “why would it not be possible to accomplish the same 100 years later, with the technology of pressurised cabins and flying at 50,000ft?”.
The PieroJet team has decades of aircraft design experience, including assisting with flight test engineering on the Dornier Seastar, building the fly-by-wire control system for the Zeppelin NT airship and working on early single-engine VTOL prototypes. The team comprises a senior air taxi operator, aeronautical engineers, an aviation patent specialist, a test pilot and an aerodynamic academic advisor.
The project has been developed so far under the Piero brand, a subsidiary of Munich-based avionics maker Moving Terrain, which Unzicker founded in 1993.
The completed pre-development of the PieroJet PJ-III is being offered through acquisition, licensing, technology transfer or joint development. The work includes extensive engineering calculations, computer-aided design design, spatial visualisation, detailed design criteria, performance and flight-dynamics computations, mission analysis and intellectual-property development. Interested parties can request a 150-page key design criteria document.
“The idea should be made known to the industry,” Unzicker tells CJI. “The defined Piero predevelopment programme is fully funded. We do not intend to establish a new aircraft factory or raise the capital required for full certification and serial production.”
The PJ-3 will have a weight of about 4,200kg, according to developers. This falls just under the 4,441kg average of the aircraft it was benchmarked against, which run from the Cessna Citation Mustang to the Piaggio Avanti. Those aircraft average a range of 1,333 miles with NBAA reserves. The PJ-3 is offered with two engine options, offering a range of about 3,000 miles.
“The team concluded it’s a solid 3,000 miles, including IFR reserves,” he says. “The aircraft carries about 1,800 litres of fuel, against about 1,500 litres for the comparison group. On long sectors it uses about half the fuel of other aircraft for the distance flown.”
The design has also been compared with midsize and super-midsize jets that fly similar distances. The three aircraft chosen – Cessna Citation Sovereign, Embraer Legacy 500 and Bombardier Challenger 300 – have an average range of 3,140 miles. Unzicker says they are about four times heavier than the PJ-3 and carry about four times as much fuel, around 7,400 litres.
“Of course, they offer a lot more. You have a flying apartment,” he says. “But not everybody needs a flying house to go from A to B.”
The Piero development team says one key to the design’s efficiency is the ratio of cabin volume to outside surface area. According to Piero, the design offers about 41sqm of outside fuselage surface. The Embraer Phenom 100, which uses the same engine and same seating capacity as Piero proposes for the PJ-3, has about 53sqm, which means about 20% more drag from the fuselage alone, says Unzicker.
From the beginning the PJ-3 was designed to fly in low friction atmosphere around 50,000ft. “For such altitudes to fly efficiently without excessive thrust a wing with extremely good gliding qualities makes most sense,” according to Piero. “The wing comprises a high aspect ratio slender wing with a supercritical profile and a special wingtip.”
Piero has patents pending, filed earlier this year, covering the fuselage shaping, an oblique bulkhead and related features. A single-engine version called the PJ-1 is next to be unveiled. It will feature a space-saving cabin interior that is also patent pending.
Most of the PJ-3 work is conventional engineering calculation. Computational fluid dynamics (CFD) analysis has been done only in part. The team will open the calculations to whoever adopts the project.
“We can make it open book. They can go through all the computations and verify it. It is not a belief. It’s maths and physics,” says Unzicker. He thinks a manufacturer’s flight physics department could check the workings to a good level of accuracy in about two weeks.
Piero’s first stage investors do not plan to build the aircraft and are not raising money from investors. “We’re not competing with aircraft companies. We’re by far not big enough to do anything like that,” he says.
The team is targeting established manufacturers of aircraft around PJ-3’s size. It is also approaching large aerospace suppliers, particularly in the Middle East, that supply major OEMs and want to build aircraft of their own.







